古建筑木结构透榫节点力学模型研究

为研究古建筑木结构透榫节点的M-θ力学模型，在分析透榫节点构造特征与受力机理的基础上，建立其数值模型，用透榫节点的试验数据验证了该数值模型的正确性，并分析了节点缝隙、木材横纹弹性模量和大榫头长度对透榫节点受弯承载力的影响。根据受力分析结果，建立以弹性点、屈服点与极限点为特征点的三折线多参数M-θ力学模型，其结果与多数的试验结果基本吻合，并将该力学模型应用于木构架的受力分析。研究结果表明：透榫节点的滞回耗能能力强，节点的变形主要集中在榫头处。当榫头与卯口之间的缝隙增大时，节点的受弯承载力降低。随木材横纹弹性模量的提高和大榫头长度的增加，节点的受弯承载力有一定提高。文章建立的M-θ力学模型能较好反映透榫节点的受力过程，适用于木构架的受力分析，其荷载 位移骨架曲线与试验结果基本吻合。研究成果可为古建筑木结构的维修与保护提供参考。     

Aqueous One-pot Synthesis of Glycopolymers by Glycosidase-catalyzed Glycomonomer Synthesis Using 4,6-Dimetoxy Triazinyl Glycoside Followed by Radical Polymerization

Glycopolymers have attracted increased attention as functional polymeric materials, and simple methods for synthesizing glycopolymers remain needed. This paper reports the aqueous one-pot and chemoenzymatic synthesis of four types of glycopolymers via two reactions: the β-galactosidase-catalyzed glycomonomer synthesis using 4,6-dimetoxy triazinyl β-D-galactopyranoside and hydroxy group-containing (meth)acrylamide and (meth)acrylate derivatives as the activated glycosyl donor substrate and as the glycomonomer precursors, respectively, followed by radical copolymerization of the resulting glycomonomer and excess glycomonomer precursor without isolating the glycomonomers. The resulting glycopolymers bearing galactose moieties exhibited specific and strong interactions with the lectin peanut agglutinin as glycoclusters.     

转速对2524铝合金搅拌摩擦点焊组织与性能的影响

对2524铝合金薄板进行搭接搅拌摩擦点焊试验, 研究了搅拌头转速对其组织与性能的影响。结果表明, 随转速增加, 焊点外侧飞边越加严重, 组织畸变程度增加, 焊核区宽度增大, 有效连接宽度先增大后减小。母材区硬度最大, 热影响区硬度最低;在焊核区内, 显微硬度随转速增加而增大, 当转速为1 100 r/min时达到最大133.9HV, 而热影响区在300 r/min时硬度最大。在单向拉伸试验中, 接头剪切强度随转速增加先增大后减小, 在700 r/min时达到最大值3 510 N;接头呈现出两种断裂模式: 即低转速下平行于两板面断裂和高转速下沿倾斜方向断裂;断口呈现明显的剪切韧窝形态, 韧窝小而浅, 焊接接头为韧性断裂。     

强变形工艺对2519A铝合金组织与性能的影响

通过硬度测试、拉伸性能测试、透射电镜观察等分析手段研究了不同强变形工艺下2519A铝合金的力学性能与微观组织。结果表明,经50%的冷轧变形和165 ℃人工时效后,2519A合金的力学性能明显提高,其抗拉强度、屈服强度和伸长率分别为522 MPa、468 MPa和8.5%。而在冷变形前添加165 ℃×2 h预时效处理,合金的力学性能进一步提高,其抗拉强度、屈服强度和伸长率分别达到535 MPa、497 MPa和8%。预时效处理可以提高合金中θ′相的密度,使析出相分布更加均匀,有助于提高合金的力学性能。     

铸态Mg-xSn-1Mn合金的显微组织和阻尼性能

采用光学显微镜(OM)、维氏硬度计、热动态分析仪、X射线衍射(XRD)、多功能内耗仪等,研究了Sn含量对Mg-xSn-1Mn合金显微组织、阻尼性能和力学性能的影响。结果表明:当Sn含量从2%增加到8%时,Mg-xSn-1Mn合金的枝晶间隙呈现细化的趋势,硬度从43.84 HV0.1增加至54.00 HV0.1,呈单调增加的趋势。应变无关阻尼随着Sn含量的增加呈现先增后减的趋势,在Sn含量为4%时达到最大,应变相关阻尼则随着Sn含量的增加呈现逐渐减小的趋势。在低温阶段,相同Sn含量的合金的阻尼随着频率的增大呈现增加的趋势;但在高温下,阻尼值在低频时的上升速率比高频时快,并随着温度的升高,低频阻尼和高频阻尼趋向于相等。当Sn含量不同时,随着温度的升高,Sn含量较高的合金的阻尼值上升速率变快。     

湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

多元合金化大断面球墨铸铁组织和性能的分析

为了提升大断面球墨铸铁综合力学性能，通过复合添加微量合金元素铜、锑、锡、钼对大断面球墨铸铁进行微合金化处理，借助金相显微镜(OM)、扫描电子显微镜(SEM)及力学性能测试等手段，研究了Cu Sb Sn Mo复合微合金化大断面球墨铸铁微观组织和力学性能。结果表明，试验球墨铸铁具有良好的综合力学性能。大断面球墨铸铁中添加铜、锑、锡、钼后优化了材料的组织结构，基体组织为珠光体＋少量牛眼状铁素体；试样石墨组织细小、圆整，分布均匀。同时，合金元素的复合加入使得其抗拉强度达到800 MPa以上，硬度约为280HB，伸长率达到5%以上。拉伸断口分析表明，微合金化大断面球墨铸铁断裂模式以解理断裂为主，伴有少量的塑性变形。     

Electrical and mechanical properties of BZT − xBCT lead-free piezoceramics

In this study, lead-free (1 − x)Ba(Zr_0.2Ti_0.8)O₃ − x(Ba_0.7Ca_0.3)TiO₃ compositions are synthesized via conventional solid oxide route, and the ceramics are fabricated with normal sintering in air. The effects of composition fluctuations on dielectric, piezoelectric, and mechanical properties are investigated. The phase structure and the microstructure are analyzed with X-ray diffraction and scanning electron microscopy. The best dielectric and piezoelectric properties of ε_r = 11 207 and d₃₃ = 330 pC/N were obtained for BZT−0.35BCT and BZT−0.5BCT ceramics, respectively. The mechanical behavior—in terms of Vickers hardness and compressive and flexural strengths—was investigated, and the best mechanical behavior was found in the vicinity of the phase transition boundary with x values between 0.5 and 0.6.     

模铸用高铝质流钢砖的显微结构分析

选取市场上模铸用高铝质流钢砖与用后残砖作为研究对象,通过检测不同高铝质流钢砖的理化性能,对比其使用前后的显微结构变化,进一步探讨模铸过程中高铝质流钢砖的显微结构对钢铁产品质量的影响。结果表明:由于显气孔率较大、结构比较疏松、烧结不致密等特性,高铝质流钢砖在经受钢水冲刷时,钢水容易渗透至高铝质流钢砖内部,加速其损毁;其次,高铝质流钢砖与钢水发生物理化学反应后在其表面生成低熔点物,使钢水中产生夹杂物,影响钢铁产品的质量。     

Antitumor Effects of Vitamin D Analogs on Hamster and Mouse Melanoma Cell Lines in Relation to Melanin Pigmentation

Deregulated melanogenesis is involved in melanomagenesis and melanoma progression and resistance to therapy. Vitamin D analogs have anti-melanoma activity. While the hypercalcaemic effect of the active form of Vitamin D (1,25(OH)₂D₃) limits its therapeutic use, novel Vitamin D analogs with a modified side chain demonstrate low calcaemic activity. We therefore examined the effect of secosteroidal analogs, both classic (1,25(OH)₂D₃ and 25(OH)D₃), and novel relatively non-calcemic ones (20(OH)D₃, calcipotriol, 21(OH)pD, pD and 20(OH)pL), on proliferation, colony formation in monolayer and soft-agar, and mRNA and protein expression by melanoma cells. Murine B16-F10 and hamster Bomirski Ab cell lines were shown to be effective models to study how melanogenesis affects anti-melanoma treatment. Novel Vitamin D analogs with a short side-chain and lumisterol-like 20(OH)pL efficiently inhibited rodent melanoma growth. Moderate pigmentation sensitized rodent melanoma cells towards Vitamin D analogs, and altered expression of key genes involved in Vitamin D signaling, which was opposite to the effect on heavily pigmented cells. Interestingly, melanogenesis inhibited ligand-induced Vitamin D receptor translocation and ligand-induced expression of VDR and CYP24A1 genes. These findings indicate that melanogenesis can affect the anti-melanoma activity of Vitamin D analogs in a complex manner.